Easy Step by Step to Wire a Pendant

Download Article

Download Article

Pendant lights can add style and personality, and come in a variety of styles that will allow you to customize any room to your liking.^[1] Replacing an old light fixture with a pendant light is a basic home improvement project that even a novice can master. The change in lighting can transform the character of a room in a matter of minutes.

1. 1

   Unpack your new fixture. Carefully lay out the parts so they are easily accessible.

2. 2

   Turn off the power. Find your home's circuit breaker or fuse box and turn off power to the room or area of the house where you'll be installing the light.^[2]

   • Failure to turn off the power before beginning work may result in serious electrical shock.

   Advertisement

3. 3

   Remove the old fixture. Unless you are installing your pendant light in a new or recently remodeled house, you'll probably need to remove an old light fixture.^[3]

   • Detach the fixture. This process will depend on the type of fixture you previously had installed. If possible, have someone hold it up while you detach it from the ceiling to decrease the likelihood of dropping it.
   • Remove the old wire connectors. These are the small plastic caps covering the connections between the fixture wires and the house wiring. Usually they can be removed by twisting them counterclockwise until loose.
   • Before disconnecting the wires, it's a good idea use a voltage checker to make sure the wires have no electricity running through them.
   • Finally, disconnect the wires and remove any remaining parts of the old fixture that are still attached to the ceiling, such as a base or trim.^[4]

4. 4

   Check your support. Make sure your installation location is structurally sound.^[5] Your electrical junction box should be supported by a beam or other support system, not simply screwed into drywall.

   • If the electrical box and light fixture are not adequately supported, it may fall. Further, this is likely a building code violation. If there is not adequate support to hold your fixture up, do not proceed with the installation.

5. 5

   Check the junction box. Make sure the screws holding the electrical box in place are tight and the box is secure. Tighten screws if necessary, but do not over-tighten.^[6]

Advertisement

1. 1

   Attach the power wires. Have an assistant hold the light fixture up to the ceiling while you connect the wires from the light fixture to those hanging out of the junction box.

   • Connect wires according to the directions provided with the light. Usually, this means connecting black to black and white to white. Wrap the exposed ends of the wires together.^[7]
   • If there is not enough exposed surface on each wire, you may need to use wire strippers to peel back some of the wire insulation.^[8]
   • Screw on wire nuts/connectors to cover the exposed connections and secure them tightly.^[9] These should be provided with the fixture, but if not, can be purchased cheaply at any hardware store.

2. 2

   Attach the ground wire. Find the ground wire on the pendant light. Depending on your wiring, you'll either wrap it around a ground screw located in the junction box or attach it to a protruding ground wire. ^[10]

   • The ground wire is usually either a green wire or a bare copper wire.^[11]
   • If you have a ground screw, tighten the screw to hold the wire in place.

3. 3

   Secure the wires. Push or fold the wiring up into the junction box, making sure that all wires remain secured together with the wire nuts.

4. 4

   Install the mounting bracket and/or mounting screws. Your new fixture should have come with a bracket and/or mounting screws needed to firmly attach the pendant light to the junction box.^[12]

   • This will vary depending on the style of light you are installing. Follow the manufacturers instructions.

5. 5

   Hang the light. Attach the canopy of or base of your light to the mounting screws or bracket.^[13] This process will also vary depending on the style of pendant light you are installing, so it's a good idea to check your directions before you start.

   • In some cases, the process is as aligning your mounting screws with some small holes in the fixture, and turning the fixture about a quarter turn.
   • In other cases, you'll have to screw the fixture into a mounting bracket.^[14]

6. 6

   Install a bulb. Screw a light bulb of the correct voltage and size into the pendant light fixture.

7. 7

   Turn the power back on. Your light should now be functional.

   • If your light does not function, turn the power back off and check your wiring.^[15]

8. 8

   Complete installation. If your fixture has a trim, a cover, or any other remaining parts that still need to be installed, install them now, and make any final adjustments to the light's height.^[16]

Advertisement

Add New Question

• Question

  Will an unconnected ground wire pendant light to junction box cause the breaker to trip?

  

  No, unless the breaker is a safety GFI type of breaker; then all wires must be connected.

• Question

  Is it possible to buy a replacement mounting bar for a pendant light?

  

  Yes, you should be able to find one at Home Depot or a good hardware store.

• Question

  What should I do with the extra cord?

  

  Try "swagging" it - if you like the look. Install a hook in the roof and loop the cord over it.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• For the best lighting results, pendant lights should be hung at a height of roughly 60 to 66 inches above the floor, or 30 inches above the surface of a table.^[17] Never install pendant lights from a ceiling where they will hang low enough for people to walk into them. Many pendant lights allow you to adjust their height.

• If you are installing pendant lights in an area where there was no light fixture to begin with, or if you are installing several mini pendants where there were fewer fixtures before, you will need to add some new wiring to your home. Unless you have experience with this, you should contact an electrician, as this task is considerably more difficult than installing a light fixture.^[18]

Thanks for submitting a tip for review!

Advertisement

• Check old wires hanging from junction box for wear or fraying before installing your new light. Don't attach your new light fixture wiring to any old wiring that shows signs of wear, including frays or burn marks. This may be a fire hazard and may also necessitate calling an electrician.

Advertisement

About This Article

Article Summary X

Before you install a pendant light, make sure you turn off the power to the room or area of the house you'll be working in so you don't shock yourself. Then, remove the old light fixture, take off the small plastic caps covering the connections between the wires, and disconnect the wires. Next, connect the wires on your pendant light to the wires hanging out of the junction box, including the ground wire. Finally, install the mounting brackets or screws, and hang up your new light. To learn how to tell if the wiring you're working with is a safety hazard, scroll down!

Did this summary help you?

Thanks to all authors for creating a page that has been read 161,188 times.

Did this article help you?

hopkinscarapt1964.blogspot.com

Source: https://www.wikihow.com/Install-a-Pendant-Light

Share this post